Unitree Robotics

Unitree G1

Unitree's 1.32 m, about 35 kg biped humanoid. Base G1 has 23 DoF; G1 EDU has 23–43 DoF, optional Dex3-1 hands and a Jetson Orin development unit.

SimulatedAvailableBipedal humanoidPublic SDK
Height
1.32 m
Mass
35 kg
Total DoF
23
Payload
2 kg

The VR operator training runs with this robot (simulation) →

Unitree G1 humanoid robot standing, front view, on a light backgroundImage: © Unitree Robotics
Unitree G1 humanoid robot standing, front view, on a light background · Source
ARworks

ARworks status by function

What works with this robot at ARworks today – and what does not.

  • Kinematic modelSimulated

    R1 training: URDF-accurate geometry, joint limits, speed limits, self- and environment collision; main dimensions within 1% of factory values. No dynamics (balance, falls, forces).

    Variant: G1 EDU · 2026-11-17
  • 3D model3D model

    Code-built, fully articulated model using the official URDF kinematics – our own work, not a vendor mesh. No 3D viewer on the website yet.

    Variant: G1 EDU · 2026-11-17
  • Walking (velocity request)Simulated

    Emulated gait within the walking limits. Known deviation: at start-up the leg joint speed can exceed the URDF limit (measured 39.7 rad/s vs 20 rad/s).

    Variant: G1 EDU · 2026-11-17
  • Arm control (IK)Simulated

    Mouse and keyboard on a laptop, clutch in VR. An unreachable target causes no jump or joint-limit violation (tested). VR verified only in the IWER emulator.

    Variant: G1 EDU · 2026-11-17
  • Hand and grasp (Dex3, single hand)Simulated

    Geometric grasp without force simulation, within the training profile limits (80 mm hand opening, 3 kg per arm). No bimanual grasp – planned (R2).

    Variant: G1 EDU · 2026-11-17
  • Head camera (D435i)Simulated

    Client-side render following the camera profile: 69° × 42° field of view, 47.6° downward tilt. The image is not a real camera stream.

    Variant: G1 EDU · 2026-11-17
  • Fault handling (latency, freeze, dropout)Simulated

    Simulated network profiles and one-off events; stale late commands are discarded by the core, a frozen image is clearly flagged (tested).

    Variant: G1 EDU · 2026-11-17
  • Unitree SDK adapterPlanned

    R4: the command mapping to the unitree_sdk2 G1 interface exists as a plan (locomotion, arm, Dex3, state); to be verified on firmware and SDK version.

    Variant: G1 EDU · 2026-11-17
  • Test on a real robotPlanned

    Not done yet. It needs the robot, firmware, peripherals, on-site supervision and a per-robot acceptance test.

    Variant: G1 EDU · 2026-11-17
Our own recordings from the training (simulation)
The Unitree G1 EDU robot card: factory and measured data labeled – simulationSimulation – real application recording
The Unitree G1 EDU robot card: factory and measured data labeled – simulation
Engineering view: the robot’s collision capsules, holding the red box – simulationSimulation – real application recording
Engineering view: the robot’s collision capsules, holding the red box – simulation
Unitree G1

Technical data

From manufacturer or primary sources. The superscript points to the source.

Geometry

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
Height1.32 m1Factorystanding1.32 m1Factorystanding
Width0.45 m1Factorystanding0.45 m1Factorystanding
Depth0.2 m1Factorystanding (thickness)0.2 m1Factorystanding (thickness)
Mass35 kg1Factorywith batteryapprox. per source35 kg1Factorywith batteryapprox.; product page 'About 35kg+', docs 'About 35kg'
Arm span0.45 m1Factoryapprox. per source0.45 m1Factoryapprox. per source

Kinematics

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
Total DoF231Factoryjoint DoF; no hand DoF listed for the base model23–431Factorydepending on configuration; per the table rows the upper value includes optional hands and extra wrist/waist joints
DoF per leg61Factory61Factory
DoF per arm51Factory51Factoryplus 2 optional wrist DoF (listed in the hand row)
Waist11Factory11Factoryplus 2 optional waist DoF
DoF per handNot published71Factoryoptional Dex3-1 force-controlled three-finger hand, per hand

Payload and locomotion

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
Payload2 kg1Factory maxarm maximum load; varies greatly with arm extension posture; per arm or total not statedapprox. per source3 kg1Factory maxarm maximum load; varies greatly with arm extension posture; per arm or total not statedapprox. per source

Actuators and hands

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
DriveLow-inertia, high-speed internal-rotor PMSM joint motors; industrial crossed roller bearings; dual encoders; hollow internal wiring; local air cooling1FactoryLow-inertia, high-speed internal-rotor PMSM joint motors; industrial crossed roller bearings; dual encoders; hollow internal wiring; local air cooling1Factory
Max joint torque90 N·m1Factory maxknee joint (largest joint motor)120 N·m1Factory maxknee joint (largest joint motor)
Hand / gripperNot publishedOptional Dex3-1 force-controlled three-finger hand (thumb 3, index 2, middle 2 active DoF), optional tactile sensor arrays1Factory

Sensing and compute

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
VisionD435i depth camera in the head2FactoryD435i depth camera in the head2Factory
Other sensingLIVOX MID-360 3D LiDAR in the head (360° horizontal, up to 59° vertical FOV); 4-microphone array; 5 W speaker2FactoryLIVOX MID-360 3D LiDAR in the head (360° horizontal, up to 59° vertical FOV); 4-microphone array; 5 W speaker2Factory
Onboard compute8-core high-performance CPU1Factory8-core CPU (motion-control unit, closed to users) + development computing unit (PC2): NVIDIA Jetson Orin NX, 16 GB memory, 2 TB storage2Factory

Energy and connectivity

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
Battery capacity9 Ah1Factoryquick-release smart batterypublished as 9000mAh (converted to Ah)9 Ah1Factoryquick-release smart batterypublished as 9000mAh (converted to Ah)
Runtime2 h1Factoryno condition statedapprox. per source2 h1Factoryno condition statedapprox. per source
Charging / swapQuick-release smart battery; 54V 5A charger1FactoryQuick-release smart battery; 54V 5A charger1Factory
ConnectivityWi-Fi 6, Bluetooth 5.21FactoryWi-Fi 6, Bluetooth 5.21Factory

Development

VariantG1base versionG1 EDUdeveloper (EDU) version; sub-versions see notes
SDK / APISecondary development not listed for the base model ('/')1FactorySecondary development supported: unitree_sdk2 (C++) with the G1 SDK Development Guide3Factory
Robot description filesURDF and MJCF in unitree_ros (g1_description: 23- and 29-DoF, with-hand and other variants)4FactoryURDF and MJCF in unitree_ros (g1_description: 23- and 29-DoF, with-hand and other variants)4Factory
SimulationMuJoCo models in the unitree_mujoco simulator (g1_23dof, g1_29dof)5FactoryMuJoCo models in the unitree_mujoco simulator (g1_23dof, g1_29dof)5Factory
Size
0.5 m1 m1.5 m2 m1.75 mPerson, 175 cm1.32 mG1
Editorial notes
  • For the arm payload (about 2 kg / about 3 kg) the maker does not say whether it is per arm or in total; the value depends strongly on the arm posture.
  • The G1 EDU sub-versions (Standard 23, Advanced 29, Ultimate A–D 29 DoF + Dex3-1 or Inspire hands) differ only in DoF and hands; the maker publishes no separate specifications.
  • The current product page publishes no walking speed.
Sources
  1. Humanoid robot G1_Humanoid Robot Functions_Humanoid Robot Price | Unitree Robotics — Unitree Robotics · checked 2026-11-17
  2. About G1 – G1 SDK Development Guide (Unitree Documentation Center) — Unitree Robotics · checked 2026-11-17
  3. Get SDK – G1 SDK Development Guide (Unitree Documentation Center) — Unitree Robotics · checked 2026-11-17
  4. unitree_ros – robots/README.md (robot descriptions) — Unitree Robotics · checked 2026-11-17
  5. unitree_mujoco (README, unitree_robots/g1) — Unitree Robotics · checked 2026-11-17
  6. xr_teleoperate – README — Unitree Robotics · checked 2026-11-17
  7. unitree_sdk2 – Unitree robot sdk version 2 — Unitree Robotics · checked 2026-11-17
  8. Unitree G1 – Unitree official store — Unitree Robotics · checked 2026-11-17
  9. unitree_rl_gym – README — Unitree Robotics · checked 2026-11-17
  10. unitree_rl_lab – README — Unitree Robotics · checked 2026-11-17

Data sheet last checked: 2026-11-17 · China · Manufacturer names and images belong to their owners. Being listed in the catalog implies no partnership or integration.

Start a project

Which robot, for what task?

Tell us the robot model, the use case and the working environment – we prepare the first meeting from that.

* required